Manosys Pressure Transmitter: EMT1

|
Model |
Indoor, drip-proof model |
Exposed terminal model |
|
EMT1A |
EMT1B |
|
|
Units Type of MeasurementMechanism Gases Measured Outer Casing Maximum Pressure Installation Electric Signal Conversion
Insulation
Resistance Operating TemperatureOperating Humidity Vibration Resistance Shock Resistance Applicable Tubing Weight |
Pa, kPa Differential
pressure Diaphragm
(silicone rubber) Air and
non-corrosive gases (no liquids) Aluminum
die-cast with gray paint 500kPa Horizontal,
facing upward (0° ± 5°) Variable
inductance Btw. terminal
& case: over 20MW (500V DC megger) 0°C ~ 50°C (no icing) 90%Rhor less
(no condensation) 5~10Hz Total
Amplitude 10mm, 10~50Hz Accelerated Amplitude 39m/s2 100m/s2
(6 times in each triaxial direction) - Soft PVC or rubber tubing (inner diameter 6 mm), for use
with vinyl tubing connector - Metal tubing (outer diameter 6 ± 0.1), for use with metal tubing connector - Hard plastic tubing (outer diameter 6 x inner diameter
4). - Inner sleeve set (XIN6x4) for use with metal tubing
connector sold separately. EMT1A: Approx:
1100g, EMT1B: Approx 960g |
|
|
Code |
|
Accuracy at 20°C |
Temperature Drift (0~40°C) |
Diaphragm Pressure Resistance |
Output & Transmittance |
|
D10 D20 D30 |
0~10 Pa 0~20 Pa 0~30 Pa |
±2%F.S. |
±0.2%F.S/°C |
10kPa |
2-wire type: Output signal 4~20 mA DC (load
resistance less than
500W) Power supply 24V DC±10% (ripple less
than 0.2V P-P) 4-wire type: Output signal 4~20 mA DC (load resistance
less than
500W) Power supply 100V AC±10%
50/60Hz About
2VA |
|
D50 D100 D200 D300 D500 D1000 |
0~50 Pa 0~100 Pa 0~200 Pa 0~300 Pa 0~500 Pa 0~1000 Pa |
Up to±1%F.S. |
Up to ±0.1%F.S./ °C |
||
|
E2 E3 E5 E10 E20 |
0~2 kPa 0~3 kPa 0~5 kPa 0~10 kPa 0~20 kPa |
40 kPa |
|||
|
E30 E50 |
0~30 kPa 0~50 kPa |
100 kPa |
|||
|
D ± 10 D ± 20 D ± 30 |
± 10Pa ± 20Pa ± 30Pa |
Up to ±2%F.S. |
Up to ±0.2%F.S/°C |
10 kPa |
|
|
D ± 50 D ± 100 D ± 200 D ± 300 D ± 500 D ± 1000 |
± 50Pa ± 100 Pa ± 200Pa ± 300Pa ± 500Pa ± 1000Pa |
Up to ±1%F.S. |
Up to ±0.1%F.S/°C |
10 kPa |
|
|
E ± 2 E ± 3 E ± 5 |
± 2 kPa ± 3 kPa ± 5 kPa |
20 kPa |
·
For
the measurement of flammable gases, or for use in a flammable atmosphere,
please use intrinsically-safe explosion-proof model EMT1H.
·
Do
not install in downward facing or vertical position
For more information, please contact:
Mihama Corporation
E-mail: info@ mihama.com
Tel: +81-3-4570-3800
Fax: +81-3-4570-3803